bright view electronics co.,ltd dice material : gan blue light color : blue color lens color : water transparent stand-off p/n : BVU-5M5BA4 r esd: 2000v(hbm) radiation pattern tolerance 0.25 L absolute maximum ratings at ta = 25 unit mw ma ma v ma/ o c electrical / optical characteristics at ta = 25 symbol unit v f forward voltage v i r reverse current a p peak emission wavelength n m d dominant wavelength n m 2 1/2 viewing angle deg i v luminous intensity mcd bin grade limits (if=20 ma) bin grade limits (if=20 ma) luminous intensity / mcd dominant wavelength / nm bin k l m n o p bin bm bn bo min. 1300 1680 2180 2800 3600 4650 min. 460 465 470 max. 1680 2180 2800 3600 4650 6000 max. 465 470 475 tolerance 15%mcd 2008/6/12 ? b parameter i f = 20 ma 30 1300 1930 *these products are sensitive to static electricity. caution must be taken strictly to avoid static electricity. i f = 20 ma 470 i f = 20 ma 465 4.0 v r = 5v 10 i f = 20 ma 3.2 lead solder temperature 1.6 mm below package 260 for 5 seconds (tsld) test cond. min. typ. max. operating temperature range (topr) 30 to 80 storage temperature range (tstg) 40 to 100 reverse voltage (v r )5 derating linear from 25 0.4 continuous forward current (i f )30 peak forward current ( 1/10 duty cycle , 0.1ms pulse width ) (i fp ) 100 parameter max. power dissipation (p d ) 120 ultra brightness led lamp BVU-5M5BA4 package configuration description *bright view reserves the rights to alter specifications and remove availability of products at any time without notice. *dominant wavelength, d is according to cie chromaticity diagram base on color of lamps. * 1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. i f = 20 ma cathode cathode 1.3 5.9 5.9 4.9 5.0 7.6 1.0 25.4min. 2.54 11.8 0.5 2.54 25.4min. 1.0 1.0min. 0.5 1.0max. 60 0 30 -60 -30 relative luminous intensity ( iv % ) 0 25 50 75 100 25 50 75 100
bright view electronics co.,ltd 2008/6/12 ? b ultra brightness led lamp BVU-5M5BA4 typical electrical / opti cal characteri stic curves ( ta = 25 c ) ( ta = 25 c ) ambient temperature ta ( c ) ambient temperature ta ( c ) 0.5 0 1.0 0 fig. 1 forward current vs. forward voltage forward current ( ma ) forward voltage vf ( v ) fig. 2 relative intensity vs. forward current relative intensity forward current if ( ma ) 1.2 fig. 3 forward voltage vs. temperature 1.1 1.0 0.9 0.8 -50 -25 0 25 50 125 100 75 -50 -25 0 0.5 1.0 1.5 2.0 2.5 3.0 fig. 4 relative intensity vs. temperature ambient temperature ta ( c ) 050 25 75 100 125 fig. 5 relative intensity vs. wavelength ( p ) wavelength ( nm ) if-dc forward current ( ma ) 0 20 40 60 80 100 120 fig. 6 maximum forward current 100 90 70 80 30 50 40 60 10 0 20 2.8 3.2 3.6 4.0 2.4 1.0 1.5 2.5 2.0 3.0 0.5 10 60 20 30 40 50 0 70 forward intensity @ 20ma 550 500 400 0 40 30 20 10 relative intensity @ 20ma forward voltage @ 20ma ( ta = 25 c ) vs. temperature 450
bright view electronics co.,ltd caution for class 1 esd ( machine mode ) gallium nitride (gan) based light emitting diodes (leds) are extremely sensitive to electrostatic discharge (esd). users are strongly recommended to take necessary meter to test the static and avoid esd when handing these products. bright view's ba, gn, wi series products are gan based materials and are classified as "class 1",( esd endurance 50v or lower ), any manufacturing site or workstation where gan devices are handled should be rated and controlled at 50v or below. proper grounding of products or machines ( via 1m ? ), using static dissipative mats, static dissipative containers, static dissipative working uniferms and shoes are considered to be effective against esd. an ionizer is recommended in the facility or environment where esd may be generated easily, and soldering iron with a grounded tip is also recommended. to install a protection device in the led circuit to ensure the surge current and voltage not exceeding the max rating during on/off swithing. when inspecting the final products in which leds are assembled, it is recommended to check whether the assembled leds are damaged by esd or not. it is simple to find damaged leds by light-on or a vf test at lower current (below 1ma is recommended). esd damaged leds will show some unusual characteristics such as the remarkable increasing of leak current, the forward voltage become lower, or the leds do not light on at the low current. 2008/6/12 ? b ultra brightness led lamp BVU-5M5BA4
bright view electronics co.,ltd apply to lamp(dip) series. description: ( 1 ) manual soldering (solder lron) (1.1) temperature at tip of the iron: 300c max. (1.2) it's banned to load any stress on the resin during soldering. (1.3) soldering time: 3 sec. max.(one time only) (1.4) leave 3mm of minimum distance from the base of epoxy. ( 2 ) dip soldering(wave solderingg-solder bath) (2.1) leave 3mm of minimum distance from the base of the epoxy. soldering beyond the base of the tie bar(stand off) is recommended. (2.2) when soldering, do not put stress on the leds during heating. (2.3) cutting the leadframes at high temperatures may cause led failure. (2.4) never take next process until the component is cooled down to room temperature after reflow. (2.5) after soldering, do not warp the circuit board. (2.6) the recommended dip soldering profile is the following: 2008/6/12 ? b ultra brightness led lamp BVU-5M5BA4 300.0 time ( sec. ) temperature ( c ) degree c. 275.0 225.0 250.0 150.0 125.0 175.0 200.0 100.0 75.0 25.0 50.0 0.0 0.0 50.0 150.0 100.0 300.0 250.0 200.0 max 260 c 5 sec. >20 c 4 c / sec. 150 c
bright view electronics co.,ltd 2008/6/12 ? b ultra brightness led lamp BVU-5M5BA4 bvu - x x x x x x x r stand-offs luminous grade -refer to the selection guide for bin options lens color -refer to lens color (1) to (9) dice code -refer to the selection guide lens configuration -refer to lens drawing view angle -refer to the selection guide (a) to (z) outline dimension -refer to the outline dimension 500pcs 20 bags 18 bags 14 bags r e y label 1 label 2 label 1 x: bin grade : wavelength : vf bvu-xxxxxxxx electronics co.,ltd. qa 29 box dimension(cm): 29*25*15 15 3mm or 5mm polybag bright view part no.: grade: lot no.: q'ty x- pcs - label 1 label 1 or label 2 attach on it. 25 type q'ty n,w g,w c.no pcs kgs kgs 3 anti-electrostatic bag electrostatic sensitive devices do not open or handle except at a static-free workstation electronics co.,ltd. bright view pcs lot no.: grade: q'ty part no.: qa caution label 2 fig. polybag / box a q'ty / polybag (pcs) device 3mm : 80,000pcs 5mm : 56,000pcs 4 boxes / carton 1000pcs blue / green / white : 36,000pcs 1000pcs 53 item no. device: q'ty pcs. n. w.: pcs. g. w.: pcs. 33 carton dimension(cm): 53*32*33 3mm(t-1) 5mm(t-1 3/4) blue / green / white 32
|
